Mr. Swards Automotive Class

Instructor: Mr. Kyle Sward • 859-744-1250 • 2748 Boonesboro Rd, Winchester KY, 40391

Maintenance & Light Repair

Section A

1st Semester

Week

Online Learning Modules

Shop Work

1 Complete Shop Safety Module 1. Rack Training, Shop Orientation
2 Engine Repair Unit 1 Quiz 1 1, 21-26. Research applicable vehicle and service information, vehicle service history, service precautions, and technical service bulletins.
3 Engine Repair Unit 1 Quiz 2 94. Verify operation of the instrument panel engine warning indicators.
4 Engine Repair Unit 1 Quiz 3 40. Inspect engine assembly for fuel, oil, coolant, and other leaks; determine necessary action.
5 Engine Repair Unit 2 Quiz 1 54. Install engine covers using gaskets, seals, and sealers as required.
6 Engine Repair Unit 2 Quiz 2 51. Remove and replace timing belt; verify correct camshaft timing.
7 Engine Repair Unit 3 Quiz 1 11. Perform common fastener and thread repair, to include: remove broken bolt, restore internal and external threads and repair internal threads with thread insert.
8 Engine Repair Unit 3 Quiz 2 111. Identify hybrid vehicle internal combustion engine.
9 Engine Repair Final 52. Adjust valves (mechanical or hydraulic lifters).
10 Automatic Transmission Unit 1 Quiz 1 35. Perform cooling system pressure and dye tests to identify leaks; check coolant condition and level; inspect and test radiator, pressure cap, coolant recovery tank, and heater core; determine necessary action.
11 Automatic Transmission Unit 1 Quiz 2 31. Inspect, replace, and adjust drive belts, tensioners, and pulleys; check pulley and belt alignment
12 Automatic Transmission Unit 1 Quiz 3 37. Remove, inspect, and replace thermostat and gasket/seal.
13 Automatic Transmission Final Test 36. Inspect and test coolant; drain and recover coolant; flush and refill cooling system with recommended coolant; bleed air as required.
14 Drive Train Unit 1 Quiz 1 33. Perform engine oil and filter change.
15 Drive Train Unit 1 Quiz 2 181. Check fluid level in a transmission or a transaxle equipped with a dig-stick.
16 Drive Train Unit 2 Quiz 1 182. Check fluid level in a transmission or a transaxle not equipped with a dip-stick.
17 Drive Train Unit 2 Quiz 2 183. Check transmission fluid condition; check for leaks.
18 Drive Train Unit 2 Quiz 3 184. Inspect, adjust, and replace external manual valve shift linkage, transmission range sensor/switch, and park/neutral position switch.

2nd Semester

Week

Online Learning Modules

Shop Work

1 Drive Train Unit 3 Quiz 1 38. Inspect for leakage at external seals, gaskets, and bushings.
2 Drive Train Unit 4 Quiz 1 185. Inspect power train mounts.
3 Drive Train Unit 4 Quiz 2 186. Drain and replace fluid and filter(s).
4 Drive Train Unit 5 Quiz 1 178. Describe the operational characteristics of a continuously variable transmission (CVT).
5 Drive Train Unit 5 Quiz 2 179. Describe the operational characteristics of a hybrid vehicle drive train.
6 Drive Train Unit 6 Quiz 1 171. Drain and refill manual transmission/transaxle and final drive unit.
7 Drive Train Final 170. Check fluid condition; check for leaks.
8 Steering & Suspension Unit 1 Quiz 1 169. Check and adjust clutch master cylinder fluid level.
9 Steering & Suspension Unit 1 Quiz 2 39. Check for system leaks.
10 Steering & Suspension Unit 2 Quiz 1 180. Describe the operational characteristics of an electronically-controlled manual transmission/transaxle.
11 Steering & Suspension Unit 2 Quiz 2 172. Inspect, remove, and replace front wheel drive (FWD) bearings, hubs, and seals.
12 Steering & Suspension Unit 3 Quiz 1 173. Inspect, service, and replace shafts, yokes, boots, and universal/CV joints.
13 Steering & Suspension Unit 4 Quiz 1 174. Clean and inspect differential housing; check for leaks; inspect housing vent.
14 Steering & Suspension Unit 4 Quiz 2 174. Check and adjust differential housing fluid level. Drain and refill differential housing. Check for leaks at drive assemny seals; check vents; check lube level.
15 Steering & Suspension Final 175. Inspect and replace drive axle wheel studs.
16 Study for Class Final 176. Inspect front-wheel bearings and locking hubs.
17 Final 98. Disable and enable supplemental restraint system (585).
18 Clean Classroom Shop Final, Clean Shop